HELLO & WELCOME

[WelshPaul]

Below are the firmware release notes (in ascending order) for the Obihai OBi504vs & OBi508vs Series Universal Adapters. These release notes describe what new features, enhancements and bug fixes are contained within a specific firmware version.

To view the very latest release notes for the Obihai OBi504vs & OBi508vs Series Universal Adapters, click here.

[WelshPaul]

Supported Products:

• OBi504vs
• OBi508vs

Firmware 4.0.2 (Build: 5492)
January 20, 2017

Features and Enhancements:

• Thawte CA G3 certificate authority support.
• New parameter called “DeviceInfo.WAN.OpenSSLCiphers” to control the ciphers used for SSL connections.
• Support X_MWIRoute and X_VMWIRoute parameters for every SP service page.
• Support using "user@obi-number" in call routing rules in the caller-id field and in the target field in the argument inside a trunk.
• Add the SpoofCallerID option under each Voice Gateway (VGn) configuration.
• Handle a URL used as DHCP Option 66 value instead of "servername."

Bug Fixes:

• If the message body starts with a SPACE or TAB, the HTTPC client parse may consider it as LWS and lead to a download failure.
• AuthUserName that contains %% cannot authenticate correctly.
• When renewing without a broadcast address, the udhcpc causes the interface to shut down.

[WelshPaul]

Supported Products:

• OBi504vs
• OBi508vs

Firmware 4.0.2 (Build: 5564)
February 15, 2017

Features and Enhancements:

• Include DigiCert SHA2 Secure Server CA certificate in firmware.
• Support custom CA cert installation using provisioning.
• Added X_MessageAccountField option (under ITSP Profile SIP page) to control where to extract mailbox account id to be used for MWI routing.
• Added MOS to X-RTP-Stat header.3.

Bug Fixes:

• 1-way audio observed when a peer sends an initial bogus RTP packet with TS=0 and SEQ=0, but sequentially switches to a normal RTP stream with different SSRC.
• MWI Routing not functional via OBiTALK.

[WelshPaul]

Supported Products:

• OBi504vs
• OBi508vs

Firmware 4.0.3 (Build: 5659)
May 19, 2017

Features and Enhancements:

• Replaced DigiCert SHA2 Secure Server CA certificate with DigiCert Global Root CA certificate.

Bug Fixes:

• Even when current encode and decode format is already G711, the OBi device is unable to identify what current decoder format is being used, it sends a redundant re-INVITE to switch the codec to G711 when FAX tone is detected. Note: This issue does not occur if RTCP is enabled on the device.
• The telephone-event RTP payload type does not change according to a peer re-INVITE. It stays at the original value established during original INVITE.
• When sending Keep Alive messages to the proxy server, the device does not follow current TCP/TLS channel to be used for REGISTER.
• LLDP: Update the Chassis ID, even if the IP address is not allocated using the network policy.
• LLDP: Update the VLAN ID and Priority value according to the network policy specified by the switch, even if the “Tagged Flag” is not set.

[WelshPaul]

Supported Products:

• OBi504vs
• OBi508vs

Firmware 4.0.4 (Build: 5677)
July 19, 2017

Features and Enhancements:

• Added support for a secondary WAN connection. When the parameter: SecondaryInterface (under WAN Settings) is configured to value: Ethernet, an additional WAN interface can be connected to Ethernet port 2-4.
• Added logic to the secondary WAN interface so it can be used as failover when the primary WAN interface detects no internet connection.
• Added support for PCAP via local UI or from the OBiTALK Device Management Platform portal.
• Added support for Speed Test from the OBiTALK Device Management Platform portal.