100 %
User avatar
By WelshPaul
Posts Signature Likes Avatar Topics
#6435
Below is my Grandstream HT812 (Firmware v1.0.33.4) configuration for use with Andrews & Arnold (AAISP) here in the UK.
(Replace +1234567890, 123456 and 01792 with your own unique parameters.)

BASIC SETTINGS
  • Time Zone: GMT (London, Great Britain)
  • Self-Defined Time Zone: GMT0BST,M3.5.0/1,M10.5.0
ADVANCED SETTINGS
  • STUN server is: stun.aa.net.uk:3478
  • Keep-alive Interval: 20
  • Firmware Upgrade and Provisioning: HTTP
  • Firmware Server Path: firmware.grandstream.com
  • Automatic Upgrade: Yes, every 10080 minutes(30-5256000).
  • Always Check for New Firmware at Boot up: Yes
  • System Ring Cadence: c=400/200-400/2000;
  • Dial Tone: f1=350@-19,f2=440@-22,c=0/0;
  • Ringback Tone: f1=400@-20,f2=450@-20,c=400/200-400/2000;
  • Busy Tone: f1=400@-20,c=375/375;
  • Reorder Tone: f1=400@-20,c=400/350-225/525-0/0;
  • Confirmation Tone: f1=1400@-10,c=0/0;
  • Call Waiting Tone: f1=400@-20,c=100/2000;
  • Prompt Tone: f1=350@-19,f2=440@-22,c=0/0;
  • Conference Party Hangup Tone: f1=400@-20,c=0/0;
  • Special Proceed Indication Tone: f1=350@-19, f2=440@-22, c=750/750-0/0;
  • NTP Server: time.aa.net.uk
PROFILE 1
  • Primary SIP Server: voiceless.aa.net.uk
  • Outbound Proxy: voiceless.aa.net.uk
  • NAT Traversal: Keep-Alive
  • Unregister On Reboot: Yes
  • Outgoing Call without Registration: No
  • Register Expiration: 1
  • OPTIONS/NOTIFY Keep Alive: OPTIONS
  • Check SIP User ID for incoming INVITE: Yes
  • Allow Incoming SIP Messages: Yes
  • MWI Tone: Special Proceed Indication Tone
  • Dial Plan: { 10[015] | 11[129] | 15[01] | 999 | 1571 | 17070 | 11[68]xxx | 08001111 | 0845464x | <=01792>[2-9]xxxxx | <141=14101792>141[2-9]xxxxx | <1470=147001792>1470[2-9]xxxxx | 0[1235789]xxxxxxxxx | 1410[1235789]xxxxxxxxx | 14700[1235789]xxxxxxxxx | 00xxx. | x+ | \+x+ | *x+ | *xx*x+ }
  • Preferred Vocoder (in listed order):
    • choice 1: PCMA
    • choice 2: PCMA
    • choice 3: PCMA
    • choice 4: PCMA
    • choice 5: PCMA
    • choice 6: PCMA
    • choice 7: PCMA
    • choice 8: PCMA
  • SLIC Setting: UK
  • Caller ID Scheme: SIN 227 - BT
  • Hook Flash Timing: In 40-2000 milliseconds range, minimum: 60 maximum: 200
  • Ring Frequency: 25Hz
  • Ring Tone 1: c=400/200-400/2000;
  • Ring Tone 2: c=400/200-400/2000;
  • Ring Tone 3: c=400/200-400/2000;
  • Ring Tone 4: c=400/200-400/2000;
  • Ring Tone 5: c=400/200-400/2000;
  • Ring Tone 6: c=400/200-400/2000;
  • Ring Tone 7: c=400/200-400/2000;
  • Ring Tone 8: c=400/200-400/2000;
  • Ring Tone 9: c=400/200-400/2000;
  • Ring Tone 10: c=400/200-400/2000;
  • Call Waiting Tone 1: f1=400@-20,c=100/2000;
  • Call Waiting Tone 2: f1=400@-20,c=100/2000;
  • Call Waiting Tone 3: f1=400@-20,c=100/2000;
  • Call Waiting Tone 4: f1=400@-20,c=100/2000;
  • Call Waiting Tone 5: f1=400@-20,c=100/2000;
  • Call Waiting Tone 6: f1=400@-20,c=100/2000;
  • Call Waiting Tone 7: f1=400@-20,c=100/2000;
  • Call Waiting Tone 8: f1=400@-20,c=100/2000;
  • Call Waiting Tone 9: f1=400@-20,c=100/2000;
  • Call Waiting Tone 10: f1=400@-20,c=100/2000;
FXS PORTS
  • SIP User ID: +1234567890
  • Authenticate ID: +1234567890
  • Password: 123456
  • Enable Port: Yes

Using Multiple Phones Behind the Same Router?
If there's more than one VoIP phone/device on the same local network, assigning each device with a different local UDP port will avoid port conflicts.

As I use multiple devices, I have changed the following parameters to suite my needs:

PROFILE 1
  • Local SIP Port: 46260
  • Local RTP Port: 46204
If you don't use multiple VoIP phone/devices on the same local network, leave the above at their default settings as shown below:

PROFILE 1
  • Local SIP Port: 5060
  • Local RTP Port: 5004
Screenshots of my configuration below:
Attachments:
basic.png
basic.png (139.79 KiB) Viewed 1712 times
advanced.png
advanced.png (240.04 KiB) Viewed 1712 times
profile_1.png
profile_1.png (391.56 KiB) Viewed 1712 times
FXS_PORTS.png
FXS_PORTS.png (39.3 KiB) Viewed 1753 times
VoipIT, tonygibbs16 and 1 others liked this
#6609
WelshPaul wrote: Fri 28th Jan 2022, 22:15 Below is my Grandstream HT812 (Firmware v1.0.33.4) configuration for use with Andrews & Arnold (AAISP) here in the UK.
(Replace +1234567890, 123456 and 01792 with your own unique parameters.)

BASIC SETTINGS
  • Time Zone: GMT (London, Great Britain)
  • Self-Defined Time Zone: GMT0BST,M3.5.0/1,M10.5.0

Screenshots of my configuration below:
Very useful post. My HT801 does not have the profile 1 & 2 options. Which firmware versions are you using please?
#6614
My HT801 was configured for another UK provider.

I read above settings and to try out, just changed SIP User IS, Authenticate ID, Password only. The phone seems to work ok with these changes.

Am I missing something by not changing the rest of the above settings?
ralphwt liked this

Hi Tony, I have just found that in the FAQ as well, se…

PSTN (analogue Phone line) to PBX

Hi, You/I need to think about FXO and FXS ports, see h…

Sip to PSTN lines gateway

Hi Dean, This product from Patton could be good for yo…

A Hook Flash is nothing more than hanging up and picki…

Sign up for VIP membership